The main body of honeycomb rotor is formed by ceramic honeycomb which is made from ceramic Dehumidification and drying: The hot and humid air from drying material barrel is blown into honeycomb rotor Material suction: material suction is to suck material from material barrel or other material container into drying
Cixi Air-Fluid Company 'BSPP Thread Metal Pneumatic Push In Fittings with below characteristics:
BSPP Thread Introductions :
The British Standard Pipe Parallel (BSPP Threads
)have the same diameter from end to end ,A
parallel thread typically seals with use of an o-ring or Back Washer to seal
the fittings ,no use of Anaerobe. The sealing ring (O-ring) can be easily
replaced if it is damaged or hard-worn with time. Connection and
disconnection of the tube can be repeated and can be performed using one hand ,
no other tools required .
Thread
Connection : Range
from BSPP 1/8" to 1/2"
Push-in
Connection: Range
from Inch Size 5/32" to 1/2" OD & Metric Size 04mm to 16MM
Configurations
Includes: Straight , Elbow , Branch
Tee ,Run Tee, Long Leg Male Elbow and Speed Control Valve .
Metal Pneumatic Push In Fittings BSPP Metal Pneumatic Push In Fittings BSPP, Pneumatic Push In Fittings, Metal Pneumatic Fittings Ningbo Air-Fluid Pneumatic Components Co., Ltd , http://www.air-fittings.com
♦ Integration of dehumidification, drying and conveying functions;
♦ Dehumidification, drying and conveying integrated unit are equipped with honeycomb rotor for getting low dew-point dry air with good stability. Cut-off valve in semi-open and fully-enclosed feed system are equipped to assure no remnants materials left in material pipe.;
♦ Equipped with micro computer and photosensor hopper for optical machine for micro powder cleaning, avoiding spot in optical products.;
♦ Stainless steel mirror polishing of all material contact surface and closed loop feeding system to avoid the material get contaminate or damp;
♦ High-performance filter to filter dusts down to 0.3um and the filtration rate can reach 99.995%;
♦ Bottom blowpipe design of material barrel with cyclone exhaust device for thermal drying barrel, to keep temperature and improvedrying efficiency;
♦ Double cooler structure to assure lower return air and dew-point.
Â
Â
fiber and organic addictive. Molecular sieve and silicone as basic material are crystallized and sintered
at high temperature for hard surface and tightly attached to the internal wall of honeycomb. Therefore,
it would not generate silt as barrel packaged or turntable molecular sieve to contaminate the plastic.
The honeycomb rotor can be used permanently and can be washed, while the ordinary molecular sieve
must be usually replaced for its easily getting saturate and aging. The water of moisture return air will be
quickly absorbed by molecular sieve when it across innumerable ostioles of the honeycomb rotor,
Therefore ,the air is completely dehumidified and reaches a very low dew-point. Regenerating and
dehumidifying happen simultaneously and follow the similar principle, except that their regeneration
air flows in the opposite direction.
after cooling. The water in air is absorbed by rotor and then desorbed by the regeneration heating air. The two
airflows workon the rotor at the same time, and as the rotor rotates, the water in air can be absorbed and desorbed continuously. Thus,a stable low dew-point air is formed and then blown into the drying barrel after heated to the
drying temperature of plastic, forming a closed loop to dry material.
material barrel. The motor starts to run when the magnetic reed switch of the vacuum hopper detects no material,
generatingvacuum in vacuum hopper, and then the material in material barrel will be sucked into vacuum hopper
because of the pressure difference of air. The motor stops working after sucking and the material will drop into
drying barrel. At last the dried material will be sucked into SVH hopper or other hopper which is set in plastic
moulding machine.
TECHNICAL SUPPORT
      XINGKE has two major production in abroad and China, with a lot of agents , representative offices and four branch in over the world ,set up the leading visualize in molding manufacturing processing
WHY US ?
*Â More than 30 years experience in plastic moulding &Â extrusion industry;
* CE,ROTH,ISO etc. certification exams passed.
* Professional sales team for overseas markets;
* High efficiency, High communicate
PRODUCTS VIEW
* Raw Materials Processing System
* Centralized Drying Dehumidifying System
*Â One-Stop Solution
* "Euro" Slow-Speed Granulators
*Â Gravimetric Blenders
*Â "Euro" Hopper Dryers
*Â All In One Dehumidifier Dryers
*Â Honeycomb Dehumidifiers
*Â Oil Heaters
* Water Cooled Chillers
FAQ
1) Are you manufacturers or trading company ?
X: Manufacturer.We produce machines in China factory and developing products from South Korea for best technical resourses , It can realize to advanced technology and reasonable cost for clients.
2)Â Do you have CE,EU,ISO9001 etc. certification ?
X:Yes , All of our products approved with these certifications.
3)Â Do you have any experience in new IMM fatory planning ?
X:Yes, also we can offer you one -Â stop solution (liquid water ,eletric,vacuum ) for your IMM or extrusion facory.Â
EXHIBITIONS
STANDARD CONFIGRAUTION
WHAT IS" HONEY-COMB "?
WORKING PRINCIPLE
SPECIFICATION
COMPANY PROFILE
         XINGKE , Officially launched the business cooperation with SHINKOR(Korea)in 2016, It has introduced a technician from Korea and focus on development of technologies to be our engineering director,The objective of XINGKE is to make "Technology as the core,customer as the oriented" becomes to solution provider for automation system.Â
PRODUCTION PROCESS