The main function of the edge banding is to seal the cross-section of the board, so as to avoid the damage of the board and the adverse factors (mainly moisture) in the process of use and prevent the formaldehyde inside the board from volatilizing, and at the same time achieve the effect of beautiful decoration.
The product has the following main features: smooth surface, no blistering, no ribbing, moderate gloss, smooth surface and back surface, uniform thickness, uniform width, reasonable hardness, high elasticity, good quality, strong wear resistance, trimmed and sealed The color of the side and the side is close to the surface color, not whitish, good gloss, and the overall color of the finished furniture is coordinated.
The role of edge banding: PVC Edge Banding For Office,Pvc Edge Banding For Office,Pvc Edge Banding For Office Table,Pvc Edge Banding For Office Furniture Henan Shunbang Chemical Industry CO.,Ltd , https://www.sbcpe.com
The LABOM Bourdon tube pressure application is extremely common and covers almost all industrial processes and scientific fields. In the heat pipe network, oil and gas transmission, water supply and gas supply systems, vehicle repair and maintenance shop and other fields can be seen everywhere. Especially in the industrial process control and technical measurement process, due to the high mechanical strength and the convenience of production, the mechanical pressure gauge has more and more extensive applications.
LABOM Bourdon tube pressure The gas density meter for SF6-gas is a pressure gauge with electrical accessories. It is mainly used in switchgear in the energy industry. It combines pressure measurement and limit switches in one device. The effect of ambient temperature is adjusted by a special compensation system. The densitometer is calibrated according to the fill pressure, calibration pressure, switch point, and ambient temperature in the application. The instrument is available in indoor models and can also be used for outdoor inflated or liquid-filled models. The measuring system is welded to the enclosure to ensure that the leak rate is at or below 10-5 mbar.l/s. Pressure gauge through the table of the sensitive components such as Bourdon tube, bellows, bellows elastic deformation, and then by the movement mechanism of the table to the pressure deformation conduction to the pointer, causing the pointer to show pressure.
First, the edge banding has the function of blocking harmful gases such as formaldehyde
Good edge banding or multi-sided edge banding can reduce the amount of formaldehyde emission per unit time (ie, slow down the emission rate). It is worth noting that edge banding will not reduce the formaldehyde content of the board, but this has the advantage of edge banding. It can reduce the formaldehyde emission per unit time of unenvironmentally-friendly sheets to a level that is acceptable to humans and does not affect health.
Second, the role of beautifying furniture
Good edge banding has the effect of beautifying office furniture, but if it is to be beautiful, the requirements for edge banding will be higher. Not only must the edge banding and the end surface of the board be firmly and smoothly combined, but also that the edge banding must be combined with other The joints of the surfaces should not have defects such as bottoming, chipping, and large gaps, and the transition should be natural, smooth and smooth.
Third, extend the service life of office furniture
The precise edge sealing design of the board can prevent water or other liquids from entering the board, avoiding the expansion, deformation and breeding of bacteria on the desktop, thereby prolonging the service life of the office furniture, and the office furniture after the edge sealing treatment is also more expensive in terms of cleaning easy.
Fourth, avoid sharp edges and corners from hurting people's bodies
The general edge banding will use the dull edge banding design to smooth the corners of the table, thereby reducing the damage to the body by the sharp corners
The LABOM Bourdon tube pressure gauge uses the elasticity sensitive element of the tube to measure the pressure by bending or torsional deformation. In the LABOM Bourdon tube pressure, one end of the Bourdon tube is fixed, and one end of the tube is active. Its sectional shape is elliptical or flat. Non-circular cross-section pipes gradually expand into a circle under the action of their internal pressure. At this time, the movable end generates a displacement that is in a certain relationship with the pressure. The movable end leads the pointer to indicate the size of the pressure. The most commonly used Bourdon tube is type C, in addition to spiral type, C type combination, and twist type. The Bourdon tube is made of copper or iron-based alloys. It is less sensitive than other pressure sensitive elements and is often used to measure large pressures. It is often used in combination with other elastic elements. Bourdon tube is still widely used in many instruments, especially for pressure and force measurement. .